Zolltarifnummer 8501640000 80 - Of an output exceeding 750 kVA

8501510000 10

- Other AC motors, multi-phase

8501000000 80

Electric motors and generators (excluding generating sets)

8501100000 80

- Motors of an output not exceeding 37,5 W

8501101000 80

- - Synchronous motors of an output not exceeding 18 W

8501101010 80

- - - For use in certain types of aircraft

8501101020 80

- - - Synchronous motor for a dishwasher with a water flow control mechanism with - a length without axle of 24 mm (+/- 0,3), - a diameter of 49,3 mm (+/- 0,3) - a rated voltage of 220 V AC or more but not more than 240 V AC, - a rated frequency of 50 Hz or more but not more than 60 Hz, - an input power of not more than 4 W, - a rotation speed of 4rpm or more but not more than 4,8rpm, - an output torque of not less than 10kgf/cm

8501101030 80

- - - Motors for air pumps, with: -operating voltage of 9 VDC or more but not more than 24 VDC, -operating temperature range of -40°C or more but not more than 80°C, -an output not exceeding 18 W  for use in the manufacture of pneumatic support and ventilation systems for car seats

8501101040 80

- - - Synchronous hybrid stepper motor with: -an output not exceeding 18 W, -two phases, -a rated current of not more than 2,5 A/phase, -a rated voltage of not more than 20 V, -with or without a threaded shaft, for use in the manufacture of 3D printers

8501101050 80

- - - Linear actuator for automotive electric seat adjustment applications: -consisting of a permanently excited DC motor with an integrated gear mechanism and leadscrew,  -whether brushed or brushless,  -whether or not with electronic control unit,  -whether or not with Hall Effect Sensor,  -with a nominal voltage of 8 V or higher but not higher than 16 V,  -with a rated output mechanical power not exceeding 20 W, and -with a specified temperature range from -40 °C to 160 °C,  for use in the manufacture of automotive components for car's seats

8501101060 80

- - - Rotary actuator for automotive electric seat adjustment applications: -consisting of a permanently excited DC motor with an integrated gear mechanism, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with Hall Effect Sensor, -with a nominal voltage of 8 V or more but not more than 16 V, -with a rated output mechanical power not exceeding 35 W, and -with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car's seats

8501101090 80

- - - Other

8501109100 10

- - Other

8501109100 80

- - - Universal AC/DC motors

8501109110 80

- - - - For use in certain types of aircraft

8501109190 80

- - - - Other

8501109300 80

- - - AC motors

8501109310 80

- - - - For use in certain types of aircraft

8501109390 80

- - - - Other

8501109900 80

- - - DC motors

8501109910 80

- - - - For use in certain types of aircraft

8501109920 10

- - - - Other

8501109920 80

- - - - - Worm axis motor for automotive electric seat adjustment applications: -consisting of a permanently excited DC motor with a worm wheel, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with Hall Effect Sensor, -with a nominal voltage of 8 V or more but not more than 16 V, -with a rated output mechanical power not exceeding 35 W, and -with a specified temperature range from -40 °C to 160 °C,  for use in the manufacture of automotive components for car's seats

8501109930 80

- - - - - Linear actuator for automotive electric seat adjustment applications: -consisting of a permanently excited DC motor with an integrated gear mechanism and leadscrew,  -whether brushed or brushless,  -whether or not with electronic control unit,  -whether or not with Hall Effect Sensor,  -with a nominal voltage of 8 V or higher but not higher than 16 V,  -with a rated output mechanical power not exceeding 20 W, and -with a specified temperature range from -40 °C to 160 °C,  for use in the manufacture of automotive components for car's seats

8501109940 80

- - - - - Rotary actuator for automotive electric seat adjustment applications: -consisting of a permanently excited DC motor with an integrated gear mechanism, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with Hall Effect Sensor, -with a nominal voltage of 8 V or more but not more than 16 V, -with a rated output mechanical power not exceeding 35 W, and -with a specified temperature range from -40 °C to 160 °C, for use in the manufacture of automotive components for car's seats

8501109950 80

- - - - - Electric (DC) motor powering height adjusting with: -a rated output mechanical power not exceeding 35 W, -frame integration with a length of 156 mm, a height of 59 mm, a thickness of 36 mm and a weight of 500 g, -a stall torque of 45 Nm and ultimate torque of 200 Nm, -a maximum current of 15 A, -no load speed of 7 RPM or more but not more than 10 RPM, -a rotation speed of 4 000 RPM or more but not more than 5 600 RPM, -a maximum noise level of 42 dB(A), -a maximum angular backlash up to 3 degrees, and -a 8 tooth pinion module, for use in the manufacture of automotive components for car's seats

8501109956 80

- - - - - DC Motor : - with a speed rotation of not more than 7000 rpm (without load), - with a nominal voltage of 12 V (± 4 V), - with a maximum power of 13,78 W ( at 3,09 A), - with a specified temperature range from -40°C to 160°C, - with a gear connection, - with a mechanical attachment interface, - with 2 electrical connections, - with a maximum torque of 100 Nm

8501109958 80

- - - - - DC Motor : - with a speed rotation of not more than 6500 rpm (without load), - with a nominal voltage of 12 V (± 4 V), - with a maximal power below than 20 W, - with a specified temperature range from -40°C to 160°C, - with a worm gear drive, - with a mechanical attachment interface, - with 2 electrical connections, - with a maximum torque of 75 Nm

8501109960 80

- - - - - DC motor - with a rotor speed of 3 500 rpm or more but not more than 5 000 rpm loaded and not more than 6 500 rpm when not loaded - with a power supply voltage of 100 V or more but not more than 240 V for use in the manufacture of electric fryers

8501109964 80

- - - - - DC motor to control angular position of the flap to adjust gas flow in the Air Throttle and EGR valve: -with Ingress Protection (IP) standard of IP69, -with a rotor speed of not more than 6 500 rpm when not loaded, -with a rated voltage of 12,0 V (± 0,1), -of a specified temperature range of - 40 °C or more but not more than 165 °C, -with or without a connecting pinion, -with or without an engine connector, -with or without a flange, -with a diameter of not more than 40 mm (not including the flange), -with an overall height of not more than 90 mm (from the base to the pinion)

8501109965 80

- - - - - Electric turbocharger actuator, with: - a DC motor, - an integrated gear mechanism, - a (pulling)force of 200 N or more at a minimum of 140°C elevated ambient temperature, - a (pulling) force of 250 N or more in each position of its stroke, - an effective stroke of 15 mm or more but not more than 25 mm, - with or without an on-board diagnostics interface

8501109970 80

- - - - - DC stepping motor, with - a two-phase winding, - a rated voltage of 9 V or more, but not more than 16,0 V - of a specified temperature range covering at least - 40 °C to + 105 °C - with or without connecting pinion - with or without motor drive connector

8501109975 80

- - - - - Permanently excited DC motor with - a multiple-phase winding - an external diameter of 28 mm or more but not more than 35 mm, - a rated speed of not more than 12 000 rpm, - a power supply voltage of 8 V or more but not more than 27 V

8501109979 80

- - - - - DC motor with brushes and an internal rotor with a three-phase winding, whether or not equipped with a worm, of a specified temperature range covering at least - 20°C to + 70°C

8501109980 80

- - - - - DC stepping motor, with: - an angle of step of 7,5° (± 0,5°), - a pull-out torque at 25 °C of 25 mNm or more, - a pull-out pulse rate of 1 500 pps or more, - a two-phase winding, and - a rated voltage of 10,5 V or more, but not more than 16,0 V

8501109990 80

- - - - - Other

8501200000 80

- Universal AC/DC motors of an output exceeding 37,5 W

8501200010 80

- - Of an output exceeding 735 W but not exceeding 150 kW, for use in civil aircraft

8501200020 80

- - Of an output of less than 750 W or exceeding 150 kW, for use in certain types of aircraft

8501200040 80

- - Universal AC/DC motor with: ­a rated output of 50 W but not higher than 1,2 kW, -a supply voltage of 230 V, ­whether or not with engine brake, ­whether or not assembled to a reduction gear with output shaft, which is contained in a housing, -whether or not fitted with a motor control/motor switch connected by cable, and -whether or not with fan, for use as electric drive of lawnmower blades or domestic appliances

8501200050 80

- - Universal AC/DC motor, rotating: -with a nominal supply voltage of 230 V, -with a power of more than 37,5 W but not more than 2 000 W, -with a stator cross-section of 93 mm or more but not more than 103 mm and a thickness of 15 mm or more but not more than 45 mm, and -with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliances

8501200060 80

- - Universal AC/DC motor, rotating: -with a nominal supply voltage of 230 V, -with a power of more than 37,5 W but not more than 1 200 W,  -with a stator cross-section of 65 mm or more but not more than 75 mm and a thickness of 15 mm or more but not more than 45 mm, and -with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliances

8501200070 80

- - Universal AC/DC motor, rotating: -with a nominal supply voltage of 230 V, -with a power of more than 37,5 W but not more than 700 W, -with a stator cross-section of 49 mm or more but not more than 59 mm and a thickness of 15 mm or more but not more than 45mm, and -with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliances

8501200090 80

- - Other

8501310000 10

- Other DC motors; DC generators, other than photovoltaic generators

8501310000 80

- - Of an output not exceeding 750 W

8501310010 80

- - - Motors of an output exceeding 735 W, DC generators, for use in civil aircraft

8501310020 80

- - - For use in certain types of aircraft

8501310045 10

- - - Other

8501310045 80

- - - - DC motors, brushless, with: - an external diameter of 90 mm or more, but not more than 110 mm, - a rated speed of not more than 3 680 rpm, - an output of 600 W or more but not more than 740 W at 2 300 rpm and at 80 °C, - a supply voltage of 12 V, - a torque of not more than 5,67 Nm, - a rotor position sensor, - an electronic star-point relay, and - for use with an electric power steering control module

8501310047 80

- - - - Motor for automotive electric seat adjustment applications: -with a shaft output on both motor sides, -consisting of a permanently excited DC motor,  -whether brushed or brushless,  -whether or not with electronic control unit,  -whether or not with Hall Effect Sensor,  -with a nominal voltage of 8 V or more but not more than 16 V,  -with a rated output mechanical power not exceeding 120 W, and -with a specified temperature range from -40 °C to 160 °C,  for use in the manufacture of automotive components for car's seats

8501310050 80

- - - - DC motors, brushless, with: - an external diameter of 80 mm or more, but not more than 200 mm, - a supply voltage of 9 V or more, but not more than 16 V, - an output at 20 °C of 300 W or more, but not more than 750 W, - a torque at 20 °C of 2,00 Nm or more, but not more than 7,00 Nm, - a rated speed at 20 °C of 600 rpm or more, but not more than 3 100 rpm, - with or without a pulley, - with or without an electronic power steering sensor/controller

8501310055 80

- - - - DC motor with or without commutator, with -an external diameter of 24,2 mm or more, but not more than 140 mm, -a rated speed of 3300 rpm or more, but not more than 26200 rpm, -a rated supply voltage of 3,6 V or more, but not more than 230 V, -an output power of more than 37,5 W , but not more than 2400 W, -a free load current of not more than 20,1 A, -a maximum efficiency of 50 % or more, for driving hand-held power tools or lawn mowers

8501310058 80

- - - - Permanently excited DC motor with: -an external diameter of 30 mm or more but not more than 90 mm, including mounting flange, -a rated speed of not more than 15 000 rpm, -an output of 45 W or more but not more than 400 W, and -a supply voltage of 9 V or more but not more than 50 V, -whether or not a multiple-phase winding, -whether or not with a drive disc, -whether or not with a crankcase, -whether or not with a fan, -whether or not with a cap assembly, -whether or not with a sun gear, -whether or not with a speed and rotational direction encoder, -whether or not with or without a speed or rotational direction sensor of resolver type or Hall effect type, -whether or not with a mounting flange

8501310063 80

- - - - Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: -a specified speed of not more than 4 100 rpm, -a minimum output of 400 W, but not more than 1,3 kW (at 12 V), or with a minimum output of 750 W but not more than 1,55 kW (at 36 V), -a flange diameter of 85 mm or more but not more than 200 mm, -a maximum length of 335 mm, measured from the beginning of the shaft to the outer ending, -a housing length of not more than 265 mm, measured from the flange to the outer ending, -a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), -a stator with single T-tooth design and single coil windings in 9/6 or 12/8 topology, and -surface magnets, -whether or not with electronic power steering controller, -whether or not with pulley, -whether or not with rotor position sensor

8501310068 80

- - - - Camshaft actuator for controlling the timing of valve opening by using electromotor in a continuous variable valve timing system of an internal combustion piston engine, of: -a length of 110 mm or more but not more than 140 mm, -a width of 90 mm or more but not more than 130 mm, -a height of 80 mm or more but not more than 110 mm for use in the manufacture of engines of motor vehicles

8501310080 80

- - - - Electronic actuator consisting of: - a DC motor having a power of less than 600 W, - for usage with a supply voltage of 12 V to 48 V, - with motor connection (plug-in connection), - with contactless position sensor, - built in a rectangular housing of a width of less than 100 mm and a length of less than 150 mm, with reduction gear and lever attached to the motor drive shaft or - in a cylindrical housing of a length off less than 150mm and with a diameter of less than 100 mm, with threads integrated into the rotor of the motor for linear movement of the integrated control rod

8501310099 80

- - - - Other

8501320000 80

- - Of an output exceeding 750 W but not exceeding 75 kW

8501320010 80

- - - For use in civil aircraft

8501320040 10

- - - Other

8501320040 80

- - - - DC motor with or without commutator, with -an external diameter of 24,2 mm or more, but not more than 140 mm, -a rated speed of 3300 rpm or more, but not more than 26200 rpm, -a rated supply voltage of 3,6 V or more, but not more than 230 V, -an output power of more than 37,5 W , but not more than 2400 W, -a free load current of not more than 20,1 A, -a maximum efficiency of 50 % or more, for driving hand-held power tools or lawn mowers

8501510000 80

- - Of an output not exceeding 750 W

8501510010 80

- - - Of an output exceeding 735 W, for use in civil aircraft

8501320065 80

- - - - Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: -a specified speed of not more than 4 100 rpm, -a minimum output of 400 W, but not more than 1,3 kW (at 12 V), or with a minimum output of 750 W but not more than 1,55 kW (at 36 V), -a flange diameter of 85 mm or more but not more than 200 mm, -a maximum length of 335 mm, measured from the beginning of the shaft to the outer ending, -a housing length of not more than 265 mm, measured from the flange to the outer ending, -a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease), -a stator with single T-tooth design and single coil windings in 9/6 or 12/8 topology, and -surface magnets, -whether or not with electronic power steering controller, -whether or not with pulley, -whether or not with rotor position sensor

8501320099 80

- - - - Other

8501330000 80

- - Of an output exceeding 75 kW but not exceeding 375 kW

8501330010 80

- - - Motors of an output not exceeding 150 kW and generators, for use in civil aircraft

8501330020 80

- - - Of an output exceding 150 kW, for use in certain types of aircraft

8501330030 80

- - - Electric drive for motor vehicles, with an output of not more than 315 kW: - with an AC or DC motor with or without transmission, - with or without power electronics

8501330099 80

- - - Other

8501340000 80

- - Of an output exceeding 375 kW

8501340010 80

- - - Generators for use in civil aircraft

8501340099 80

- - - Other

8501400000 80

- Other AC motors, single-phase

8501402000 80

- - Of an output not exceeding 750 W

8501402010 80

- - - Of an output exceeding 735 W, for use in civil aircraft

8501402020 80

- - - For use in certain types of aircraft

8501402035 80

- - - Electric AC motor, single-phase, with: -a rated power of 120 W or more but not more than 150 W, -an input power of 280 W or more but not more than 350 W, -an external diameter without bracket connector and pulley of 145 mm or more but not more than 160 mm, -a rated speed of 2 680 rpm or more but not more than 3 000 rpm, -a weight of 4,2 kg or more but not more than 4,6 kg, -pulleys, a spindle and a tachometer, for use in the manufacture of home appliance products

8501402045 80

- - - Electric AC motor, single-phase, with: -a rated power of 275 W or more, but not more than 325 W,  -an input power of 600 W or more but not more than 700 W, -an external diameter without bracket and connector of 150 mm or more but not more than 170 mm, -a rated speed of 15 000 rpm or more but not more than 20 000 rpm, -a weight of 4,2 kg or more, -a pulley and a tachometer, for use in the manufacture of home appliance products

8501402050 80

- - - Electric AC motor, single-phase, with: -a rated power of 300 W or more but not more than 370 W,  -an input power of 600 W or more but not more than 700 W, -an external diameter without bracket and connector of 150 mm or more but not more than 170 mm, -a rated speed of 15 000 rpm or more but not more than 19 000 rpm, -a weight of 4,8 kg or more, -a pulley, for use in the manufacture of home appliance products

8501402055 80

- - - Electric AC motor, single-phase, with: -a rated power of 275 W or more, but not more than 325 W,  -an input power of 600 W or more but not more than 700 W, -an external diameter without bracket and connector of 160 mm or more but not more than 180 mm, -a rated speed of 15 000 rpm or more but not more than 19 000 rpm, -a weight of not more than 4,4 kg, -a pulley, for use in the manufacture of home appliance products

8501402060 80

- - - Electric AC motor, single-phase, with: -a rated power of 275 W or more but not more than 325 W,   -an output power of 550 W or more but not more than 600 W, -an input power of 800 W or more but not more than 1 000 W, -an external diameter of more than 150 mm but not more than 170 mm without the bracket, -a rated speed of more than 16 000 rpm but not more than 18 000 rpm, -a weight of 3,4 kg or more but not more than 3,7 kg, -a pulley, for use in the manufacture of home appliance products

8501402065 80

- - - Electric AC motor, single-phase, whether or not with commutator - with a nominal output of 180 W or more, - with an input power of 150 W or more but not more than 2 700 W, - with an external diameter of more than 120 mm (± 0,2 mm) but not more than 135 mm (± 0,2 mm), - with a rated speed of more than 10 000 rpm but not more than 50 000 rpm, - whether or not equipped with air-inducting ventilator, - whether or not with mechanical device (pinion, screws, gear connection etc.) on the shaft, for use in the manufacture of domestic appliances

8501402080 80

- - - Other

8501408000 80

- - Of an output exceeding 750 W

8501408010 80

- - - Of an output not exceeding 150 kW, for use in civil aircraft

8501408020 80

- - - Of an output exceeding 150 kW, for use in certain types of aircraft

8501408050 80

- - - Electric drive for motor vehicles, with an output of not more than 315 kW: - with an AC or DC motor with or without transmission, - with or without power electronics

8501408060 80

- - - Electric AC motor, single-phase, whether or not with commutator - with a nominal output of 180 W or more, - with an input power of 150 W or more but not more than 2 700 W, - with an external diameter of more than 120 mm (± 0,2 mm) but not more than 135 mm (± 0,2 mm), - with a rated speed of more than 10 000 rpm but not more than 50 000 rpm, - whether or not equipped with air-inducting ventilator, - whether or not with mechanical device (pinion, screws, gear connection etc.) on the shaft, for use in the manufacture of domestic appliances

8501408090 80

- - - Other

8501510020 80

- - - Of an output of less than 750 W, for use in certain types of aircraft

8501510030 80

- - - AC synchronous servo motor with resolver and brake for a maximum speed of not more than 6 000 rpm, with: - an output of 340 W or more but not more than 7,4 kW, - a flange of dimensions of not more than 180 mm !x! 180 mm, and - a length from flange to extreme end of resolver of not more than 271 mm

8501510040 80

- - - Electric AC motor, three-phase, with: -a rated power of 280 W or more but not more than 320 W, -an output power of 480 W or more but not more than 540 W,  -an input power of 800 W or more but not more than 900 W, -an external diameter of 150 mm or more but not more than 170 mm, -a rated speed of 15 000 rpm or more but not more than 20 000 rpm,  -a weight of 6 kg or more but not more than 6,4 kg, -a pulley and a tachometer, for use in the manufacture of home appliance products

8501510050 80

- - - Three phase AC synchronous brushless permanent magnet motor with: -an output of 500 W or more but not more than 700 W,  -an external diameter of 129,7 mm or more but not more than 180,3 mm,  -a rated speed of 16 000 rpm or more but not more than 17 000 rpm, -a weight of 2,5 kg or more but not more than 3,1 kg, and -with a pulley, for use in the manufacture of home appliance products

8501510090 80

- - - Other

8501520000 80

- - Of an output exceeding 750 W but not exceeding 75 kW

8501522000 80

- - - Of an output exceeding 750 W but not exceeding 7,5 kW

8501522010 80

- - - - For use in civil aircraft

8501522050 10

- - - - Other

8501522050 80

- - - - - AC synchronous servo motor with resolver and brake for a maximum speed of not more than 6 000 rpm, with: - an output of 340 W or more but not more than 7,4 kW, - a flange of dimensions of not more than 180 mm !x! 180 mm, and - a length from flange to extreme end of resolver of not more than 271 mm

8501522089 80

- - - - - Other

8501523000 80

- - - Of an output exceeding 7,5 kW but not exceeding 37 kW

8501523010 80

- - - - For use in civil aircraft

8501523090 80

- - - - Other

8501529000 80

- - - Of an output exceeding 37 kW but not exceeding 75 kW

8501529010 80

- - - - For use in civil aircraft

8501529090 80

- - - - Other

8501530000 80

- - Of an output exceeding 75 kW

8501535000 80

- - - Traction motors

8501535010 80

- - - - Electric drive for motor vehicles, with an output of not more than 315 kW: - with an AC or DC motor with or without transmission, - with or without power electronics

8501535020 80

- - - - AC traction motor of the Interior Permanent Magnet Synchronous Motor (IPMSM) type with: -a torque output of 200 Nm or more, but not more than 400 Nm, -a power output of 50 kW or more, but not more than 200 kW , -a rotation speed of no more than 15 000 rpm, for use in the manufacture of electric vehicles

8501535030 80

- - - - Permanent magnet synchronous traction motor, with: -a continuous power of 110 kW or more but not more than 180 kW, -a liquid cooled system, -a total length of 500 mm or more but not more than 650 mm, -a total width of 600 mm or more but not more than 700 mm, -a total height of 550 mm or more but not more than 650 mm, -weighing of not more than 350 kg, -3 suspension points

8501535040 80

- - - - Permanent magnet traction AC motor, with: -a continuous power of 110 kW or more but not more than 150 kW, -a liquid cooled system, -a total length of 460 mm or more but not more than 590 mm, -a total width of 450 mm or more but not more than 580 mm, -a total height of 490 mm or more but not more than 590 mm, -a weight of not more than 310 kg, -4 mounting points

8501535090 80

- - - - Other

8501538100 10

- - - Other, of an output

8501538100 80

- - - - Exceeding 75 kW but not exceeding 375 kW

8501538110 80

- - - - - Of an output not exceeding 150 kW, for use in civil aircraft

8501538120 80

- - - - - Of an output exceeding 150 kW, for use in certain types of aircraft

8501538190 80

- - - - - Other

8501539400 80

- - - - Exceeding 375 kW but not exceeding 750 kW

8501539410 80

- - - - - For use in certain types of aircraft

8501539490 80

- - - - - Other

8501539900 80

- - - - Exceeding 750 kW

8501539910 80

- - - - - For use in certain types of aircrafts

8501539990 80

- - - - - Other

8501610000 10

- AC generators (alternators), other than photovoltaic generators

8501610000 80

- - Of an output not exceeding 75 kVA

8501612000 80

- - - Of an output not exceeding 7,5 kVA

8501612010 80

- - - - For use in civil aircraft

8501612090 80

- - - - Other

8501618000 80

- - - Of an output exceeding 7,5 kVA but not exceeding 75 kVA

8501618010 80

- - - - For use in civil aircraft

8501618099 80

- - - - Other

8501620000 80

- - Of an output exceeding 75 kVA but not exceeding 375 kVA

8501620010 80

- - - For use in civil aircraft

8501620040 80

- - - AC, 3-phase generator, with: -a continuous power of 147 kVA or more but not more than 222 kVA, -a continuous torque of 650 Nm or more but not more than 900 Nm, -a maximum working speed of 2700 revolutions per minute (rpm), -a liquid cooled system, -a length of 100 mm or more but not more than 200 mm, -a width of 550 mm or more but not more than 650 mm, -a height of 550 mm or more but not more than 650 mm, -weighing of not more than 150 kg

8501620098 80

- - - Other

8501630000 80

- - Of an output exceeding 375 kVA but not exceeding 750 kVA

8501630010 80

- - - For use in civil aircraft

8501630099 80

- - - Other

8501710000 10

- Photovoltaic DC generators

8501710000 80

- - Of an output not exceeding 50 W

8501720000 80

- - Of an output exceeding 50 W

8501800000 80

- Photovoltaic AC generators